Posted on 4 Comments

BMW Series 5 Hybrid Battery Pack Teardown

Here’s something I didn’t think I’d be doing! Here’s a teardown of a BMW 5 Series G30 530E Hybrid Battery pack – a monster 351V, 9.2kWh Lithium pack, obtained for it’s cells to replace the boat’s aging lead acids.

This is something I didn’t have the safety gear to do right of the bat – opening one of these packs is a potentially lethal exercise, with 6 unfused battery modules in series, quite capable of blowing pieces off a nice conductive sack of salt water like a person. Cue the purchase of high-voltage rated gloves for protection, just while I got the pack split into something more manageable.

Needless to say, the combination of current capacity & voltage present in EV or Hybrid vehicle battery packs is nothing short of lethal, and these units should be treated with considerable respect.

Hybrid Battery Pack
Hybrid Battery Pack

Here’s the beast of a battery. Enclosed in an aluminium cast housing, it’s very heavy, and definitely not a one-man lift!

Cover Removed
Cover Removed

After removing the top cover, secured by combination Torx/10mm hex bolts, the internals of the pack are visible. There’s no sealant on the cover, just a large rubber gasket, so this came off easily. There are 6 individual modules in this pack, all wired in series with massive links. There’s also a cooling system for each battery module, supplied with refrigerant from the car’s AC system – there’s a TXV mounted on the side of the battery pack. I didn’t see any heaters present, but I don’t know if BMW have done any neat reverse-cycle magic to also heat the modules if required using the AC system on the car.

Left Side Modules
Left Side Modules

The modules are arranged 3 to a side, double-stacked at the back, then a single module at the front. The pack would normally sit under the rear seats of the vehicle, hence the unusual shape. The refrigerant lines going to the evaporators on this side of the pack can be seen in the bottom right corner.

Output Cables & Contactor Pack
Output Cables & Contactor Pack

The main contactor pack is on the left side, just behind the massive DC output connector. I’ll dig into this in another post later on.

Right Side Modules
Right Side Modules

The right side of the pack is arranged much the same as the left, the main difference here being the battery ECU is tucked in at the top here, along with the interface connector to the car, and the refrigerant lines to the TXV on the outside, which I’ve already removed. Each module has a cell balance control unit, in this case one is mounted on the top of a module, and on the side of the module in the lower right corner.

Cooling Evaporator
Cooling Evaporator

Once all the modules have been removed, the evaporator matrix is visible on the bottom, a series of very thin aluminium tubes, designed for the best contact with the aluminium frame of the battery modules.

Module Cell Layout
Module Cell Layout

Popping the plastic insulating cover off the battery module reveals the internal construction. I’ve not been able to find exact data on these cells, but I’m assuming them to be a similar chemistry to the ones used in the BMW i3 packs, so 4.15v Max, 3.68v nominal, 2.7v Minimum. The alloy frame itself is of laser welded construction, and there are 16 cells in series per module, giving about 58.8v per module. These will need to be reconfigured as 4 sets of 4 cells in series for 14.72v.
All the individual cell taps are nicely loomed down the middle of the module to each cell, and there are 3 temperature sensors per module (the red epoxy blobs).

Cell Welded Links
Cell Welded Links

The individual cell links are laser welded to the terminals of the cells, so this does make life a little more difficult when it comes to reconfiguring them. The links appear to be made from Aluminium, so soldering is going to be a bit more tricky than usual.

4 thoughts on “BMW Series 5 Hybrid Battery Pack Teardown

  1. this is awesome, thank you for sharing

  2. this is awesome thank you so much for sharring

  3. I currently own a 530e. After reading through, it seems like wasting time to think that it is possible to upgrade/swap packs to 18650(Tesla) cells to increase battery/range capacity. But what do you of possibility? And if it can be done at some point, do you think it would ever be greatly increased from 9.2kw?
    *530e max driving range of 18-19miles without using any of ac/heater/radio.

    1. Hi William,

      I don’t know how far you’d get with such a project – you’d need to build completely new modules, and the voltage profiles of the cells BMW are using may be more different than I know – I only took a guess that they’re similar in chemistry to the i3 cells for which there is some public data.
      Different cells may get damaged, or full capacity may not get used. The BMS may not even register healthy cells.
      If you can do this on the cheap, it may be worth a go though!

      Cheers

Leave a Reply to Gregski Cancel reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.