power – Page 6 – Experimental Engineering

Posted on September 23, 2010 by The Engineer — Leave a comment

Belkin F5U021 4-Port USB Hub

This is an old USB 1.1 hub that was recently retired from service on some servers. Top of the unit visible here.

Bottom label shows that this is a model F5U021 hub, a rather old unit.

PCB is here removed from the casing, Indicator LEDs along the bottom edge of the board, power supply is on the left. Connectors on the top edge are external power, USB host, & the 4 USB outputs. Yellow devices are polyswitch fuses for the 500mA at 5v each port must supply.

This is the USB Hub Controller IC, which is a Texas Instruments TUSB2046B device. Power filter capacitors next to the USB ports are visible here also, along with 2 of the polyswitches.

The power supply section of the unit, which supplies regulated 5v to the ports, while supplying regulated 3.3v to the hub controller IC. Large TO-220 IC is the 5v regulator. Smaller IC just under the power selector switch is the 3.3v regulator for the hub IC. The switch selects between Host powered or external power for the hub.

Posted on September 22, 2010 by The Engineer — 2 Comments

Epson Ink Cartridge Resetter

This is a device designed to reset Epson brand ink cartridges that are reportedly out of ink, so they again report full to the printer Here is the front of the unit, with the guide for attaching to a cartridge.

Back of the device removed. 3 button cells provide power to the PCB. Indicator LED sticks out of the top of the device for reset confirmation.
Row of pads on far left edge of the PCB are presumably a programming header for the uC on the other side of the board.

Here is the front of the PCB, main feature being the grid of pogo pins to connect to the cartridge chip. IC on lower right of that is a MSP430F2131 uController, a Texas Instruments part.
The IC directly to the left of the pogo pin bed is a voltage regulator, to step down the ~4.5v of the batteries down to the ~3.3v that the uC requires.

Posted on August 26, 2010 by The Engineer — Leave a comment

Nokia 7110

Another phone from the mid 90s. This is the nokia 7110.

Here the slider is open showing the keypad.

Here the battery is removed, a Li-Ion unit.

The battery cell & protection circuit removed from the casing.

This is the rear of the PCB removed from the housing. Data & charging ports on the right hand side f the board.

Front of the PCB with the RF sections at the left hand side & the keypad contacts on the right.

Closeup of the RF sections of the board, big silver rectangular cans are VCO units.

Closeup of the top rear section of the PCB, with SIM cnnector, battery contacts, IR tranciever at the far left. Bottom centre is the external antenna connector.

The logic section of the board, Large chip is CPU, to right of that is the ROM storing the machine code. Other chips are unknown custom parts.

The Mic & the loudspeaker removed from it’s housing.

LCD from the front of the unit, SPI interfaced. Flex PCB also contains the power button, loudspeaker contacts & a temperature sensor.

The scroll wheel removed from the front housing.

Tiny vibration motor removed from the rear housing, alerts the user to a text or phone call.

Posted on August 25, 2010 by The Engineer — Leave a comment

Dremel MultiPro

Here we have a Dremel MultiPro rotary tool, a main powered 125W 33,000RPM bit of kit.

Here the field & controller assembly is removed from the casing.

Here is the armature, which rotates at up to 33,000RPM. The brushes rise against the commutator on the left, next to the bearing, the cooling fan is on the right hand side on the power output shaft, the chuck attaches at the far right end of the shaft.

Here is the speed controller unit, inside is an SCR phase angle speed controller, to vary the speed of the motor from 10,000RPM to the full rated speed of 33,000RPM.

This is the mains filter on the input to the unit, stops stray RF from the motor being radiated down the mains cable.

Posted on July 31, 2010August 1, 2010 by The Engineer — 2 Comments

Current Cost ‘Envi’ CC128 Power Meter

This is the Current Cost CC128 Real Time Power Meter. Shown here is the display unit, British Gas issued these free to some customers.
This unit measures current power draw in Watts, cost of power currently being used (requires unit price to be set), overall kWh usage over the past 1, 7 or 30 days & power trends during the day, night & evening. Also displays current time & current room temperature.

Here the front panel of the display has been un-clipped. At the bottom are the RJ-45 serial port & power connections.
This unit uses a PIC micro-controller as it’s CPU (PIC18F85J90) Just above & left of the CPU is the 433MHz SPD radio receiver module. The chips on the right of the CPU are a 25LC128 SPI serial EEPROM for data storage & a 74HC4060 14 stage binary counter, to which is connected the 32kHz clock crystal. The red wire around the top of the display is the antenna for the radio receiver.

For more info on the CC128 in general, the serial port & software for computer data logging, see this link
See this link for Current Cost’s list of software

Closeup of the ICs on the mainboard.

Here we have the transmitter unit, with Current Transformer (CT). The red clamp fits around one of the electric meter tails & read the current going to the various circuits. This unit is powered by 2x D cells, rated at a life of 7 years.

The PCB inside the transmitter. Again very minimal design, unknown controller IC, 433MHz radio transmitter on right hand side with wire antenna. Two barrel connectors on left hand side of board allow connection of up to two more CT clamps for measurement of 3-phase power. Centre of board is unmarked header. (ICSP?)

CT unit. Inside is a coil of wire & an iron core which surrounds the cable to be measured.

PIC18F85J90