August 2010 – Experimental Engineering

Posted on August 26, 2010 by The Engineer — Leave a comment

Motorola V360v

Here is a more modern phone, the Motorola V360v. Features include Dual screens, 640×480 VGA camera, full col

our TFT Main LCD, SD-Micro slot.
Here on the back the grey scale LCD can be seen, with the camera lens to the right of the Motorola logo

Here the phone is opened showing the keypad & the full colour TFT LCD display.

Here the battery is removed from the unit, showing the SIM connector. The antenna cover is still on at the bottom.

The antenna cover has been removed in this shot, the antenna is the white section at the bottom, With the loudspeaker & the external antenna connector hidden at the right.

Here is the main PCB. Parts from left are the Bluetooth module at the top, supplied by Broadcom, the SD Card socket at the bottom. Main CPU next to that is the Freescale SC29343VKP. Above right of the CPU is the Freescale SC13890P23A Charger, Power & Audio IC. Below is the SIM card socket. Under the main CPU is the Intel Flash memory IC. ICs inside the shields are the RF sections for transmit & receive.

Rear of the display unit showing the monochrome LCD. The camera module on the bottom left. Ear speaker on the far right of the unit.

Main colour TFT LCD.

Camera module removed from the LCD unit.

The vibration motor attached to one of the LCD looms.

Posted on August 26, 2010 by The Engineer — Leave a comment

Nokia 7110

Another phone from the mid 90s. This is the nokia 7110.

Here the slider is open showing the keypad.

Here the battery is removed, a Li-Ion unit.

The battery cell & protection circuit removed from the casing.

This is the rear of the PCB removed from the housing. Data & charging ports on the right hand side f the board.

Front of the PCB with the RF sections at the left hand side & the keypad contacts on the right.

Closeup of the RF sections of the board, big silver rectangular cans are VCO units.

Closeup of the top rear section of the PCB, with SIM cnnector, battery contacts, IR tranciever at the far left. Bottom centre is the external antenna connector.

The logic section of the board, Large chip is CPU, to right of that is the ROM storing the machine code. Other chips are unknown custom parts.

The Mic & the loudspeaker removed from it’s housing.

LCD from the front of the unit, SPI interfaced. Flex PCB also contains the power button, loudspeaker contacts & a temperature sensor.

The scroll wheel removed from the front housing.

Tiny vibration motor removed from the rear housing, alerts the user to a text or phone call.

Posted on August 25, 2010 by The Engineer — Leave a comment

Dremel MultiPro

Here we have a Dremel MultiPro rotary tool, a main powered 125W 33,000RPM bit of kit.

Here the field & controller assembly is removed from the casing.

Here is the armature, which rotates at up to 33,000RPM. The brushes rise against the commutator on the left, next to the bearing, the cooling fan is on the right hand side on the power output shaft, the chuck attaches at the far right end of the shaft.

Here is the speed controller unit, inside is an SCR phase angle speed controller, to vary the speed of the motor from 10,000RPM to the full rated speed of 33,000RPM.

This is the mains filter on the input to the unit, stops stray RF from the motor being radiated down the mains cable.

Posted on August 25, 2010 by The Engineer — Leave a comment

Ericsson GA628

Here is a phone from the mid 90s, the Ericsson GA628. Here visible is the front of the unit with keypad, & single line monochrome LCD for number display.

Here the battery is removed from the phone, showing the SIM card socket. At the top under the antenna stub is the socket for an external antenna.

Here the front is removed from the phone, PCB on left, rear of keypad on right. Microphone is at bottom of keypad, with speaker at the top. Top right of the PCB is the ringer buzzer, left is shield for RF amplifier.

Here is the back of the main PCB, RF sections on left & centre. Processing & memory on right.

This phone had a Ni-Mh battery, before Li-Ion batteries were introduced.

The LCD from the front of the phone is shown here. A simple dot matrix single line unit.

Posted on August 5, 2010 by The Engineer — Leave a comment

HP Photosmart 375

This is a HP PhotoSmart 375 portable photo printer. With built in card reader, screen & PictBridge.
Top of the printer showing the UI Buttons & Screen.

Front of the unit, card reader slots at the top, Pictbridge USB connector at top left. Paper out slot at bottom. Cartridge door is on the right.

Here the cartridge door is open. Takes HP 95 Tri-Colour Inkjet Cartridge.

Battery compartment on the bottom of the unit. A Li-Ion battery pack can be installed here for mobile photo printing.

Specifications label.

Power adaptor & USB connection for PC use.

Rear door opened. Showing the paper feed tray.

Rear door has been removed in this shot. Paper feed roller & platen roller can be seen here.

Paper holder attached to rear door.

Bottom of the top cover, with connections for the buttons & LCD panel.

This is the main PCB of the unit. Controls all aspects of the printer. CPU in center, card reader sockets are along bottom edge. various support circuitry surrounds the CPU.

Rear shell has been removed here. Showing the main frame & the carriage drive motor on the left.

Closeup of the carriage drive motor & timing belt system. All the motors in this printer are DC servo motors, not steppers.

Main drive motor, feeds paper, drives rollers, operates cleaning mechanism for the inkjets.

Mainshaft encoder. Main drive motor is bottom right hand side with timing belt drive.

Closeup of the CPU. This is a Phillips ARM chip, unknown spec.

Detail of the card reader sockets, this unit takes all current types of Flash memory card.

HP 95 Tri-color Inkjet Print Cartridge

Posted on August 2, 2010 by The Engineer — 1 Comment

ICL Barcode Scanner

An ICL barcode scanner from the 80s is shown here. This is the top of the unit with cover on.

Plastic cover removed from the unit showing internal components. Main PSU on left, scan assembly in center. Laser PSU & Cooling fan on right. Laser tube at top.

Closeup of laser scan motor. This unit scans the laser beam rapidly across the glass plate to read the barcode.

View of the bottom of the unit, showing the controller PCB in the centre.

The 3-phase motor driver circuit for the scan motor. 15v DC powered.

This is the laser unit disconnected from the back of the scanner. HT PSU is on right hand side, beam emerges from optics on left.

This unit is date stamped 1987. The oldest laser unit i own.

Laser tube power supply. Input voltage: 24v DC. Output: 1.8kV 4mA.

Rear of HT PSU. Obviously the factory made a mistake or two 🙂

Top cover removed from the laser unit here shows the 1mW He-Ne tube. Manufactured by Aerotech.

Tube label. Manufactured July 1993. Model LT06XR.

Here the tube has been removed from it’s mount to show the bore down the centre while energized.

OC end of the tube shown here lasing.

Beam output from the optics on the laser unit.

Optics built into the laser unit. Simple turning mirror on adjustable mount & collimating lens assembly.

Kind of hard to see but the unit is running here & projecting the scan lines on the top glass.

Laser tube mounting. A combo of spring clips & hot glue hold this He-Ne tube in place

Posted on August 1, 2010 by The Engineer — Leave a comment

Hair Dryer

This is a 1500W hairdryer, death caused by thermal switch failure.

This is the switch unit. Attached are two suppression capacitors & a blocking diode. Cold switch is on right.

Heating element unit removed from housing. Coils of Nichrome wire heat the air passing through the dryer. Fan unit is on right.

Other side of the heating element unit, here can be seen the thermal switch behind the element winding. (Black square object).

The fan motor in this dryer is a low voltage DC unit, powered through a resistor formed by part of the heating element to drop the voltage to around 12-24v. Mounted on the back of the motor here is a rectifier assembly. Guide vanes are visible around the motor, to straighten the airflow from the fan blades.

5-blade fan forces air through the element at high speed. Designed to rotate at around 13,000RPM.